Shvidko to spend your first good look, and come again. To save that hour of pennies, rather, I would like to vindicate the stencil. What is the best way of vibrating the walls to choose how to carry out all the work?

Roughness assessment of surface walls

All methods of viriving walls are subdivided into two fundamentally different groups:

What's the other way choose To this, this stage is especially important. Those who are nervous, you can die laser level and the most important everyday level.

The sequence of work looks like this:

1. preparation of surface walls. Sobish, scho virivnyu, trimalasya, the wall is necessary with a proper rank. All the excesses of the old coating are removed, then a primer is carried out for short adhesion from the plaster ball. For cement, store the vicorist primer in different sizes and water, so called cement milk, for gypsum plaster, it is better to use vicorist;
   
2. if the ball of plaster will be larger than 2 cm, then at this stage it is better to reinforce plaster grid yak not to allow the warehouse to obsipatisya. Varto means that if you have a ready-made factory plaster bag, then you need to bring respect to the warehouse: deyakі virobniki vikoristovuyut polymer additives, like flooring zbіlshuyut mіtsnіst i steps prilipannya rozchina, scho sіtka may not be needed.
3. installation of beacons. Like beacons, like beacons, they become a guide for folding even surfaces, vicarious wooden slats or perforating metal profiles. The rest will be good for beginners, the shards of such lighthouses will not be able to be hit after a light hardening of the plaster ball and then mask the ditching. On the back, two lighthouses are mounted at the opposite ends of the wall, at the same time, and the lighthouses are reinforced with plaster of paris of the required height until they reach the ideal verticality. Between the two beacons, stretch out three cords: in the mountains, in the middle of the wall, and below, and even focusing on them, install the intermediate beacons so that the stench lightly sticks out the cord. Krok mizh beacons to lie down in the rozmіru іnstrumentu, as a way to rozrіvnyuvatimetsya stucco sumіsh (sound for this vicorist rule). Have a vipadka, stand between beacons can be 20 cm less for a tool;
4. 
   you can find a wide range of products at the budіvelnyh shops. On the weekly maidan, it is no longer enough to properly prepare the cuts, supplementing the instructions. Cement plastering can be prepared independently: mix cement and sand at a ratio of 1:6, then add water to a creamy consistency. Deyakі fahivtsі recommend dorimuvatisya spіvvіdnoshnja komponentіv 1:2 or 1:3, ready sumіsh to go plastic, and therefore, simple to use. Ready-made rozchin vikoristovuyut stretch 1-2 years, the docks of wines do not catch;
5. applied plaster. For whom it is possible to vicorate "sokіl" and a trowel. For the first one, collect the sum from the room, for the others, throw yoga on the wall near the overworld kilkost. The vikoristannya "falcon", an instrument similar to a trowel, but overturns yoga in dimensions, allowing greater speed of the work performed. Now, as a rule, it is necessary to spread the roses evenly from the bottom of the hill, spiraling to the lighthouses. As a ball, which virіvnyuє, tovst, then you can put a rough tent of plaster on the back, and then apply the main one on the beacons. As if the rest of the wooden slats were victorious, then if the pieces were dried out, they need to be neatly beaten, filled with empty plaster and leveled with a spatula;
6. 
   after the hanging of the plaster, it is equal, but the surface is short. In order to make it smooth, it is necessary to apply thin ball of putty, and then sand the surface with a fine sandpaper.

The main advantage of such a method of virіvnyuvannya is the maximum conservation of the core area of ​​\u200b\u200bthe room. Minuses lie in the laboriousness of the process, the need to prepare the basis for the presence of a large number of saws.

No. 2. Restoration of walls with putty

Tim is not smaller, don’t forget that this is such a way to vindicate walls take away the rich brown area and if it won’t, and if it’s in deficit, then the room will risk transforming into a hole. Walls, sheathed with sheets of drywall, can be less stressful, less plastered. How to go about the application of advanced moisture, next to vicoristing water-resistant sheets of drywall.

Sequence of work:

1. 
   arguing the frame. Vin can be folded for a metal profile. The beam does not allow the reach of the bazhan durability of the frame, which is slicker to the vpliv of moisture and microorganism, which in most cases vikoristovuyutsya today straight and rigid metal profile.
   The first two profiles are attached to the footer of that stele.
   On the slope, with additional help, draw a straight line with a winder of 5-6 div in the wall (more is possible, as the curvature is great to cover the communication).
   For the help of the vertical scale, transfer the line to the stele.
   On otrimanih lines with screws to fasten straight profiles, gradually reversing the jealousy of their equal for the help of the scheme. Between them, perpendicular to them, vzdovzh walls to fix bearing profiles for help. Vіdstan mіzh them 40-60 cm for sheets gypsum plasterboard curtains 120 cm;